The DIY Gas Tank Fuel Sight Gauge Kit from Lowbrow Customs. What makes our kit different than others available? Start with the smooth 90 degree fittings, chromed brass, 1/8″ NPT x 1/4″ hose barb, made in the USA. Mild steel tophat 1/8″ NPT bungs, easy to weld, drill a 5/8″ hole and drop them in and they held in place perfectly by the flange. Stainless steel hose clamps with stainless screw, made in the USA, and then polished to a show quality finish. 10″ of high-quality 1/4″ ID polyurethane clear fuel line, this is very flexible and has excellent fade and abrasion resistance.

Check out the Gas Tank Fuel Sight Gauge Kit install article in our DIY Tech Tips section!

Lowbrow Customs is proud to be distributed in the U.S.A by Drag Specialties. Drag part # 0706-0224

Lowbrow Fuel Reserve Bottle. Holds 30 fl. oz. (887 ml) of fuel, some extra miles to get you off of the side of the road and to a gas station. These are ultra light, seamless extruded aluminum. Lacquered interior for superior durability and protection. These are NOT water bottles! For go juice only. O-ring sealed cap. Height 10 5/8 and Diameter 3 1/8.

The DIY Gas Tank Fuel Sight Gauge Kit from Lowbrow Customs. What makes our kit different than others available? Start with the smooth 90 degree fittings, chromed brass, 1/8″ NPT x 1/4″ hose barb, made in the USA. Mild steel tophat 1/8″ NPT bungs, easy to weld, drill a 5/8″ hole and drop them in and they held in place perfectly by the flange. Stainless steel hose clamps with stainless screw, made in the USA, and then polished to a show quality finish. 10″ of high-quality 1/4″ ID polyurethane blue fuel line, this is very flexible and has excellent fade and abrasion resistance.

Check out the Gas Tank Fuel Sight Gauge Kit install article in our DIY Tech Tips section!

The DIY Gas Tank Fuel Sight Gauge Kit from Lowbrow Customs. What makes our kit different than others available? Start with the smooth 90 degree fittings, chromed brass, 1/8″ NPT x 1/4″ hose barb, made in the USA. Mild steel tophat 1/8″ NPT bungs, easy to weld, drill a 5/8″ hole and drop them in and they held in place perfectly by the flange. Stainless steel hose clamps with stainless screw, made in the USA, and then polished to a show quality finish. 10″ of high-quality 1/4″ ID polyurethane red fuel line, this is very flexible and has excellent fade and abrasion resistance.

Check out the Gas Tank Fuel Sight Gauge Kit install article in our DIY Tech Tips section!

Lowbrow Customs is proud to be distributed in the U.S.A by Drag Specialties. Drag part # 0706-0225

The DIY Gas Tank Fuel Sight Gauge Kit from Lowbrow Customs. What makes our kit different than others available? Start with the smooth 90 degree fittings, chromed brass, 1/8″ NPT x 1/4″ hose barb, made in the USA. Mild steel tophat 1/8″ NPT bungs, easy to weld, drill a 5/8″ hole and drop them in and they held in place perfectly by the flange. Stainless steel hose clamps with stainless screw, made in the USA, and then polished to a show quality finish. 10″ of high-quality 1/4″ ID polyurethane sky blue fuel line, this is very flexible and has excellent fade and abrasion resistance.

Check out the Gas Tank Fuel Sight Gauge Kit install article in our DIY Tech Tips section!

The Narrow Frisco Sporty Tank is the amalgamation of steel and chopper style with undertones of a MoCo heritage. This custom gas tank holds approximately 2.5 gallons and will give your bike style for miles. Featuring:

One-piece stamped 16-gauge steel top and bottom
TIG welded tank seams and mounting tabs
Lathe-turned, hand-brazed threaded steel cap bung
Vented alloy gas cap included
Hand-brazed fuel bung accepts 22mm threaded petcocks

Tanks are pressure tested at the factory, but it is highly recommended you or your painter pressure test it again before painting; it’s cheap insurance!

One great way to save money at the pump is to buy less at every fill-up. At just 2 gallons, our new P-Nut is about as small as a chopper tank can get. Lower fuel capacity means you’ll have more time for bumming smokes and shooting the shit at every gas stop. The Lowbrow P-Nut tank features heavy gauge steel construction (tank shells are stamped from 1mm (approx. 19 ga. steel) , 1/4″ NPT petcock bungs and undrilled DIY mounting tabs for custom installation. It takes a British-style gas cap for unparalleled chopper authenticity.

Nothing changes the look of your hand-built death trap like a new gas tank. Lowbrow Customs is stoked to be offering this Wassell style peanut tank. No more scouring eBay or swap meets and over-paying for an old tank that is rusty, crusty, and likely needs work to repair leaky seams. Our tanks are heavier gauge than the originals, brand new and ready to rock!

Produced in a partnership between Lowbrow Customs & Cleveland CycleWerks.

Tanks are pressure tested at the factory, but it is highly recommended you or your painter pressure test it again before painting; it’s cheap insurance!

Tank Measurements: The total length is 14-1/2″ (16-3/4″ end of tab to end of tab), 7-1/2″ tall (8-3/8″ to top of filler bung), and 8-3/4″ at the widest point. The tunnel measures 1-3/4″ wide, 2-1/4″ deep at the tank rear and 5-3/4″ deep at the front of the tunnel.

Lowbrow Customs is proud to be distributed in the U.S.A by Drag Specialties. Drag part # 0701-0710

The exact same great P-Nut tank, but with the mounting tabs included but unwelded. This allows you to fab custom mounts, or weld the included tabs on exactly how you want.

One great way to save money at the pump is to buy less at every fill-up. At just 2 gallons, our new P-Nut is about as small as a chopper tank can get. Lower fuel capacity means you’ll have more time for bumming smokes and shooting the shit at every gas stop. The Lowbrow P-Nut tank features heavy gauge steel construction (tank shells are stamped from 1mm (approx. 19 ga. steel) , 1/4″ NPT petcock bungs and undrilled DIY mounting tabs for custom installation. It takes a British-style gas cap for unparalleled chopper authenticity.

Nothing changes the look of your hand-built death trap like a new gas tank. Lowbrow Customs is stoked to be offering this Wassell style peanut tank. No more scouring eBay or swap meets and over-paying for an old tank that is rusty, crusty, and likely needs work to repair leaky seams. Our tanks are heavier gauge than the originals, brand new and ready to rock!

Produced in a partnership between Lowbrow Customs & Cleveland CycleWerks.

Tanks are pressure tested at the factory, but it is highly recommended you or your painter pressure test it again before painting; it’s cheap insurance!

Tank Measurements: The total length is 14-1/2″, 7-1/2″ tall (8-3/8″ to top of filler bung), and 8-3/4″ at the widest point. The tunnel measures 1-3/4″ wide, 2-1/4″ deep at the tank rear and 5-3/4″ deep at the front of the tunnel.

Lowbrow Customs is proud to be distributed in the U.S.A by Drag Specialties. Drag part # 0701-0711

The DIY Gas Tank Fuel Sight Gauge Kit from Lowbrow Customs. What makes our kit different than others available? Start with the smooth 90 degree fittings, chromed brass, 1/8″ NPT x 1/4″ hose barb, made in the USA. Mild steel tophat 1/8″ NPT bungs, easy to weld, drill a 5/8″ hole and drop them in and they held in place perfectly by the flange. Stainless steel hose clamps with stainless screw, made in the USA, and then polished to a show quality finish. 10″ of high-quality 1/4″ ID polyurethane yellow fuel line, this is very flexible and has excellent fade and abrasion resistance.

Check out the Gas Tank Fuel Sight Gauge Kit install article in our DIY Tech Tips section!